| Quantity: | |
|---|---|
ST-260
SINOTECH
8474809090
70mm
52.9g/s
1210mm
260Ton
26.7kW
63.7A
8.55Ton
480L
| Item | | 260SElll | ||
| Screw diameter | mm | 55 | 60 | 70 |
| Theoretical shot volume | cc | 713 | 848 | 1155 |
| Shot weight (PS) | g | 649 | 772 | 1051 |
| Shot weight (PS) | oz | 22.9 | 27.3 | 37.1 |
| Length/Diameter ratio | L/D | 22.9 | 21 | 18 |
| Injection pressure | MPa | 211 | 178 | 131 |
| Injection rate | cm⊃3;/sec | 237 | 282 | 384 |
| Injection stroke | mm | 300 | ||
| Max. Screw speed | rpm | 175 | ||
| Plasticizing capacity (PS) | g/s | 32.3 | 35.2 | 52.9 |
| Injection unit force | Ton | 9.1 | ||
| Carriage stroke | mm | 350 | ||
| Clamping force | Ton | 260 | ||
| Max. daylight | mm | 1210 | ||
| Clamping stroke | mm | 600 | ||
| Distance btwn. Tie bars | mm | 580*580 | ||
| Min mould dimension | mm | 400*400 | ||
| Mould thickness range | mm | 195-610 | ||
| Ejector force | Ton | 11.1 | ||
| Ejector stroke | mm | 180 | ||
| No. of ejector pins | unit | 13 | ||
| Max. motor power | kW | 26.7 | ||
| System pressure | MPa | 17.5 | ||
| Hydraulic pump capacity | L/min | 172 | ||
| No. of heater zones | unit | 5+1 | ||
| Heater input power | kW | 18.9 | ||
| Ultimate capacity | kw | 46.6 | ||
| Current | A | 63.7 | ||
| Net weight | Ton | 8.55 | ||
| Oil filling capacity | L | 480 | ||
| Item | | 260SElll | ||
| Screw diameter | mm | 55 | 60 | 70 |
| Theoretical shot volume | cc | 713 | 848 | 1155 |
| Shot weight (PS) | g | 649 | 772 | 1051 |
| Shot weight (PS) | oz | 22.9 | 27.3 | 37.1 |
| Length/Diameter ratio | L/D | 22.9 | 21 | 18 |
| Injection pressure | MPa | 211 | 178 | 131 |
| Injection rate | cm⊃3;/sec | 237 | 282 | 384 |
| Injection stroke | mm | 300 | ||
| Max. Screw speed | rpm | 175 | ||
| Plasticizing capacity (PS) | g/s | 32.3 | 35.2 | 52.9 |
| Injection unit force | Ton | 9.1 | ||
| Carriage stroke | mm | 350 | ||
| Clamping force | Ton | 260 | ||
| Max. daylight | mm | 1210 | ||
| Clamping stroke | mm | 600 | ||
| Distance btwn. Tie bars | mm | 580*580 | ||
| Min mould dimension | mm | 400*400 | ||
| Mould thickness range | mm | 195-610 | ||
| Ejector force | Ton | 11.1 | ||
| Ejector stroke | mm | 180 | ||
| No. of ejector pins | unit | 13 | ||
| Max. motor power | kW | 26.7 | ||
| System pressure | MPa | 17.5 | ||
| Hydraulic pump capacity | L/min | 172 | ||
| No. of heater zones | unit | 5+1 | ||
| Heater input power | kW | 18.9 | ||
| Ultimate capacity | kw | 46.6 | ||
| Current | A | 63.7 | ||
| Net weight | Ton | 8.55 | ||
| Oil filling capacity | L | 480 | ||
